Premium YachtsSpain
SeaStorm 17 motor boat on the water

SeaStorm Boats dealer in Spain

SeaStorm Boats in Spain

Practical one-piece HDPE motor boats for days on the water.

Explore SeaStorm models

Compare the SeaStorm 12, 13S, 14 and 17 and ask Premium Yachts Spain for a current model-specific quotation.

SeaStorm Boats

SeaStorm Boats through Premium Yachts Spain

SeaStorm builds rotationally moulded HDPE boats with UV-stabilized material. Select a model by size, intended use and published power limits, then confirm the engine, accessories and delivery in a tailored quotation.

  • Rotationally moulded one-piece HDPE construction
  • Four models with distinct sizes and power limits
  • Engine, accessory and trailer choices confirmed by quotation

HDPE

Why SeaStorm HDPE boats are different

SeaStorm describes a one-piece, rotationally moulded polyethylene hull. The mould is rotated while the material forms the shell, rather than building up a conventional GRP laminate and gelcoat.

Practical durability

A tough, flexible hull material can be useful around docks and during frequent handling. It is not damage-proof; inspect the hull, fittings and fastenings as you would on any boat.

Care without conventional gelcoat

The HDPE hull can be washed and does not have a conventional gelcoat finish. UV stabilizers are included in the material. Engines, steering, upholstery and hardware still need routine care.

Material and design

HDPE material is recyclable. Hull shape and on-water behaviour differ by model; SeaStorm describes the 13S as having a double-step hull. Do not assume identical performance across the range.

CHOOSING A HULL

HDPE, GRP, inflatable or aluminium?

Hull material is one part of the decision. This guide compares typical care and handling considerations, not specific boats tested under identical conditions.

ConsiderationSeaStorm HDPEGRP / fibreglassInflatable / RIBAluminium
ConstructionOne-piece rotationally moulded polyethylene hull.Laminated composite hull, often with gelcoat.Inflatable tubes; a RIB also has a rigid hull, often GRP or aluminium.Fabricated metal hull; construction varies by builder.
Dock contactFlexible hull material can tolerate routine knocks; inspect any damage.Gelcoat can chip or scrape; inspect the laminate after a hard impact.Tubes can cushion contact but need checks for cuts and air loss.Dents and coating damage are possible; inspect after impact.
Sun and weatherSeaStorm uses UV-stabilized material; fading and ageing remain possible.Finish needs care; exposure and condition vary.Tube ageing depends on fabric, exposure and storage.Coatings and fittings need condition checks.
Saltwater and fittingsHDPE hull does not rust; metal fittings and engine still need care.Hull does not rust; fittings and engine still need care.Tube seams, rigid hull, fittings and engine all need checks.Corrosion control depends on alloy, coatings, fittings and maintenance.
CleaningWash the hull and remove growth after use; avoid strong solvents.Clean and maintain the finish as the builder recommends.Clean tubes using products suitable for their fabric.Wash and protect the finish as the builder recommends.
Surface finishNo conventional gelcoat; ask about suitable treatment for the intended mooring pattern.Gelcoat or paint may need polishing or repair.Tube fabric and rigid-hull finish have separate care needs.Painted or bare finishes need different care.
Repair routeAssess the damage; structural HDPE work needs an appropriate specialist.Composite or gelcoat repair depends on the damage.Tube repair and rigid-hull repair are different jobs.Metal or coating repair depends on the alloy and damage.
Handling and storageCheck the actual model weight, lifting points and approved trailer.Check the actual model weight, lifting points and trailer.Some inflatables pack down; RIBs retain a rigid hull.Check the actual model weight, lifting points and trailer.
Fleet planningCompare cleaning time, impact exposure and written commercial warranty terms.Allow for finish care and inspection in the service plan.Plan tube checks and eventual fabric service alongside hull care.Plan coating, fitting and corrosion inspections.

Construction

SeaStorm HDPE
One-piece rotationally moulded polyethylene hull.
GRP / fibreglass
Laminated composite hull, often with gelcoat.
Inflatable / RIB
Inflatable tubes; a RIB also has a rigid hull, often GRP or aluminium.
Aluminium
Fabricated metal hull; construction varies by builder.

Dock contact

SeaStorm HDPE
Flexible hull material can tolerate routine knocks; inspect any damage.
GRP / fibreglass
Gelcoat can chip or scrape; inspect the laminate after a hard impact.
Inflatable / RIB
Tubes can cushion contact but need checks for cuts and air loss.
Aluminium
Dents and coating damage are possible; inspect after impact.

Sun and weather

SeaStorm HDPE
SeaStorm uses UV-stabilized material; fading and ageing remain possible.
GRP / fibreglass
Finish needs care; exposure and condition vary.
Inflatable / RIB
Tube ageing depends on fabric, exposure and storage.
Aluminium
Coatings and fittings need condition checks.

Saltwater and fittings

SeaStorm HDPE
HDPE hull does not rust; metal fittings and engine still need care.
GRP / fibreglass
Hull does not rust; fittings and engine still need care.
Inflatable / RIB
Tube seams, rigid hull, fittings and engine all need checks.
Aluminium
Corrosion control depends on alloy, coatings, fittings and maintenance.

Cleaning

SeaStorm HDPE
Wash the hull and remove growth after use; avoid strong solvents.
GRP / fibreglass
Clean and maintain the finish as the builder recommends.
Inflatable / RIB
Clean tubes using products suitable for their fabric.
Aluminium
Wash and protect the finish as the builder recommends.

Surface finish

SeaStorm HDPE
No conventional gelcoat; ask about suitable treatment for the intended mooring pattern.
GRP / fibreglass
Gelcoat or paint may need polishing or repair.
Inflatable / RIB
Tube fabric and rigid-hull finish have separate care needs.
Aluminium
Painted or bare finishes need different care.

Repair route

SeaStorm HDPE
Assess the damage; structural HDPE work needs an appropriate specialist.
GRP / fibreglass
Composite or gelcoat repair depends on the damage.
Inflatable / RIB
Tube repair and rigid-hull repair are different jobs.
Aluminium
Metal or coating repair depends on the alloy and damage.

Handling and storage

SeaStorm HDPE
Check the actual model weight, lifting points and approved trailer.
GRP / fibreglass
Check the actual model weight, lifting points and trailer.
Inflatable / RIB
Some inflatables pack down; RIBs retain a rigid hull.
Aluminium
Check the actual model weight, lifting points and trailer.

Fleet planning

SeaStorm HDPE
Compare cleaning time, impact exposure and written commercial warranty terms.
GRP / fibreglass
Allow for finish care and inspection in the service plan.
Inflatable / RIB
Plan tube checks and eventual fabric service alongside hull care.
Aluminium
Plan coating, fitting and corrosion inspections.

These are general material considerations, not performance, safety, lifespan or ownership-cost rankings. Design, equipment, build quality, storage and operating conditions matter. A RIB may have a GRP or aluminium rigid hull, so the categories can overlap.

What matters for a rental or day-charter fleet

A washable hull and tolerance of frequent handling may appeal to operators. Standardizing models and equipment may also simplify training and spare-parts planning. Every boat still needs scheduled engine, steering, electrical and safety-equipment maintenance. Compare the actual model, permitted use, passenger limits, local authorization, insurance, repair support and written warranty terms before choosing a fleet.

A 20-year limited manufacturer hull warranty

SeaStorm states that the original retail purchaser has limited hull coverage for material and workmanship defects, subject to the published conditions, exclusions and claim procedure. The manufacturer decides repair or replacement under its terms. The published spare-parts warranty is two years. Engines and trailers have their own manufacturers’ terms. Coverage for rental or charter use is not confirmed and must be obtained in writing before commercial purchase.

Read SeaStorm warranty terms

Compare the four SeaStorm models

Manufacturer specifications are useful for shortlisting. Choose the boat against your intended use and the actual operating permissions, not a universal “best” model.

ModelLengthBeamCE design capacityMaximum power
SeaStorm 123.66 m1.67 mC4 / D630 hp
SeaStorm 13S4 m1.9 mC5 / D560 hp
SeaStorm 144.28 m1.86 mC5 / D640 hp
SeaStorm 175.17 m1.97 mC6 / D880 hp

CE categories and numbers are design ratings, not commercial passenger authorizations.

SeaStorm

SeaStorm boats for day charter and rental fleets

Compact layouts, a washable HDPE hull and colour choices may make these boats worth considering for small-group outings, rental operations or resort activities. Buying several similarly equipped boats may simplify familiarization and service planning; no cost saving is promised.

Professional suitability is not the same as commercial authorization. Model, passenger limits, operating area, registration, inspection, insurance and licensing must be checked for the intended activity. CE design capacity does not establish a permitted charter passenger count in Spain.

Looking to build a SeaStorm rental fleet?

Tell us the operating area, intended activity, number of boats and preferred models. We can discuss engines, colours, accessories, trailers and delivery before preparing a current quotation.

Configure a fleet enquiry

SeaStorm

SeaStorm model range

Compare the SeaStorm 12, 13S, 14 and 17 and ask Premium Yachts Spain for a current model-specific quotation.

SeaStorm 12 on the water

HDPE motor boat

SeaStorm 12

A rotationally moulded HDPE boat for practical time on the water. Ask for the current configuration and a quotation for Spain.

Starting from

€5,523

Advantage boat. Delivery excluded; request a current quote.

Explore SeaStorm 12
SeaStorm 13S on the water

HDPE motor boat

SeaStorm 13S

A rotationally moulded HDPE boat for practical time on the water. Ask for the current configuration and a quotation for Spain.

Starting from

€8,287

Advantage boat. Delivery excluded; request a current quote.

Explore SeaStorm 13S
SeaStorm 14 on the water

HDPE motor boat

SeaStorm 14

A rotationally moulded HDPE boat for practical time on the water. Ask for the current configuration and a quotation for Spain.

Starting from

€8,994

Advantage boat. Delivery excluded; request a current quote.

Explore SeaStorm 14
SeaStorm 17 on the water

HDPE motor boat

SeaStorm 17

A rotationally moulded HDPE boat for practical time on the water. Ask for the current configuration and a quotation for Spain.

Starting from

€13,551

Advantage boat. Delivery excluded; request a current quote.

Explore SeaStorm 17

SeaStorm

Accessories and trailers

Explore manufacturer-listed engines, accessories and trailers. Compatibility and package contents are confirmed for the selected model in a quotation.

  • Model comparison and specification guidance
  • Engine and accessory configuration review
  • Quotation and delivery coordination

SeaStorm questions

Are prices shown for SeaStorm boats?

Yes. Each model shows a starting price for the SeaStorm Advantage boat. Ask for a current quotation covering your chosen engine, accessories and delivery destination.

Are trailers and engines included?

Package contents and model compatibility must be confirmed in the quotation.

Start a conversation

Discuss a SeaStorm boat

Tell us which model you are considering and how you plan to use it. We will confirm current equipment, price and delivery terms. Your enquiry will be sent to Premium Yachts Spain with SeaStorm Boats and SeaStorm range already identified.